Data Sheet. Pin Flash Microcontrollers .. 18F14K Example. -I/ML. . Original data sheet for PIC18F1XK22/LF1XK22 devices. Revision B . 18F14K22 Datasheet, 18F14K22 PDF, 18F14K22 Data sheet, 18F14K22 manual , 18F14K22 pdf, 18F14K22, datenblatt, Electronics 18F14K22, alldatasheet. Greetings again — I have been working with the 18F14K22 (mask rev pg of the data sheet indicates it takes Fosc/4 scales it from there.

Author: Nilrajas Nasho
Country: Jordan
Language: English (Spanish)
Genre: Environment
Published (Last): 11 April 2018
Pages: 394
PDF File Size: 12.49 Mb
ePub File Size: 1.98 Mb
ISBN: 196-1-67808-257-2
Downloads: 79044
Price: Free* [*Free Regsitration Required]
Uploader: Voodoom

When you start the project, the main. You should be able to compile the code without datashete error or warning. The code given above does nothing.

Its just a way to make sure you programming environment is set properly. In order to set the pin of PIC controller you need to know the registers associated with it. There are 3 registers.

If you write into LAT, it is equivalent to writing directly to the pin. But if you read from LAT bits, you will be reading the buffer, not the voltage at the pin. Instead if you use PORT bits, you will directly to the pin and read from it. But please read the datasheet to know more. So we need to add some delay. You got to set some delay.

XC compiler gives you delay function, but you need to set a few parameters well actually its one line. Comments 32 Trackbacks 0 Leave a comment Trackback albhee June 30th, at But i have question. It is more of a C language question. If you want to do what you are trying to do, then try using switch-case. Where do you see it?

What file are you talking about? Never mind about the LAT sentence, as you say it they are not defined for this pic.


But I will check the structure on pic16fh.

Do you know why? I have this problem with all ports except the port D Im ussing pic16f and pic16f But 18g14k22 through the header file, looks like there are no definition for LAT bits. So you can only use port bits. The stuff written here are for 18F series. I would suggest you to try microchip forums.

They are pretty fast. I started using Pic18f with xc8 compiler.

CCS :: View topic – 18F14K22 – int ref and timer2 issues ..

In the above program you first declared the internal oscillator freq in conf file. I am new to uc dahasheet, excuse me for basic doubts.

Thank you for your reply. Hi this tutorial really helped me. But I am having problem. Please check the declaration and source files which will answer a lot.

Have you got any idea on why that happens? Never came across a problem like that.

I checked it and I saw that also RA2 pin has that thing. Thank you so much! All tutorial is datasheef And I tryed to use all pins of A bank as input and also to connect the input directly to Vdd or ground. Please turn off ADC on the pins you want to use as Output and it will start working.


In order to set the pins as DIO, please read the chapter 8. Hi and thank you for your great tutorials. I try to explain it better: I tryed some simple programs with only outputs RC are connected to 4 led and they works good. I tryed to connect directly with a cable the pin to Vdd but nothing changes, I tryed with the switch on the demoboard connected catasheet RA2 pin of the mcu, checked with a tester directly on that pin, when switch is not pressed, it get 4.

For those tests Vdd is provided by an USB of my pc. I have a question though, Is it possible to refer to a single register bit by index?


PIC 18F14K22 DIL20, 8-BIT, 16K Flash | Microchip

The TRISx list is actually a structure. If you right click and go to declaration of TRISx, you will be able to see the source and find a way to define the way you want. RBO already addresses one bit. I dont want to enable PLL….

Here is a microchip device documentation on oscillators: Are you sure you need an external oscillator? Datasheet justification for it? Younesser, You need to make your own config.

Here is the config. Also you 18f4k22 refer to my previous posts on how to create your config file. Singular Engineer In progress…. IO ports April 14th, singularengineer Leave a comment Go to comments.

Comments 32 Trackbacks 0 Leave a comment Trackback. June 30th, at Hi, Thank you for this tutorial. May 6th, at May 7th, at March 19th, at Hi, I am beginner in microcontrollers programming and I have several doubts. Could you help me? My first quetion is: January 3rd, at Thank you very much for your reply!! January 1st, at Thank you very much for your tutorial!! You are a genius! May 30th, at Hello, I started using Pic18f with xc8 compiler.

I am new to uc programming, excuse me for basic doubts Thanks.

March 25th, at March 24th, at February 14th, at February 13th, at October 18th, at August 15th, at June 17th, at June 10th, at E-Mail will not datashest published required. Subscribe to comments feed. Is it worth it? Categories Blog Electronics Projects.

Sorry, your blog cannot share posts by email.