Download DesignJet C Service from folder Printers DesignJet. DesignJet C Service Manual pdf. From folder: Printers HP DesignJet. View and Download HP C user manual online. DRAFTING PLOTTERS SERVICE MANUAL. C Plotter pdf manual download. Also for: Designjet c . Service Manual and more parts for CA DesignJet c printer.

Author: Kami Yozshulkree
Country: Antigua & Barbuda
Language: English (Spanish)
Genre: Relationship
Published (Last): 5 March 2017
Pages: 163
PDF File Size: 13.73 Mb
ePub File Size: 15.29 Mb
ISBN: 981-7-40950-809-2
Downloads: 94477
Price: Free* [*Free Regsitration Required]
Uploader: Shaktik

The first mannual depicts the block of text shown on the plot and in Tablebut the remaining blocks show the memory location number instead of the contents at each position on the text block. Pen Carriage Assembly See Page Interaction between the settings produces the ten modes. Don’t have an account? After clearing, cycle power without media, and do the following calibrations in the order listed: Page 39 Action buttons: Disconnect the carriage motor cable connector labeled C from the interconnect PCA.

HP 650C User Manual

When the front panel instructs you, lower the pinchwheel lever. User Information And Operation shiny side up. The Virtual Agent is currently unavailable. See Table for a list of system error codes and their respective descriptions and rec- ommended corrective actions. Unable to determine warranty status. To install the sled during reassembly, see Figure and do the following: Also See for C Specification sheet – 1 page Frequently asked questions manual – 37 pages.

Plotter window must be closed. Access Pens brings the pen carriage out to the plotting area for pen access.

  BGP RFC 1771 PDF

HP DesignJet Printer series User Guides | HP® Customer Support

Disconnect the media sensor cable connector from the main PCA. This feature can be used to ensure proper data reception. It is switched ON and OFF by the servo pro- cessor and is mounted in the electronics enclosure at the rear of the plotter. To remove the platen roller assembly, perform the following procedure: Introduction This chapter contains diagnostic instructions, error codes and messages, service tests, and troubleshooting information for use as an aid in solving Model CA and CA De- signJet C plotter symptoms and failures.

Page Service Station See Page The regulator will then adjust the voltage to bring it back to the optimum value. Button Test The display indicates which button the servo processor interprets as being pressed. In roll media opera- tions, the user can choose desifnjet continuous plotting or cutting plots off the roll automati- cally as they are completed.

CA See Page Some error messages require action to clear, and others are only displayed until the next operation is per- formed by the plotter. Switch the plotter OFF and disconnect the ac power cord and interface cable from the desugnjet. Page Use the Drop detect calibration, found in the service menu to recalibrate the position of the sensor.

We are unable to determine your warranty status for the product and serial number provided. The block of text on the configuration plot that shows the contents of the EEROM appears in the form shown in Table Feed the rubber tubes through the slot in the bottom of the service station housing while lowering the sled mahual position.

  CAPOTE MUSIC FOR CHAMELEONS PDF

If the user selects another mode while plotting, the plotter waits until desognjet current plot is finished and then switches to the newly selected mode. The pen carriage moves out from the pen service sta- tion at the left of the plotter and stops in front of the slot in the bail.

HP DesignJet 650 Printer series User Guides

Refer to Table to determine when calibrations are required. Using a TORX T-8 screwdriver, remove the two screws that attach the window sen- sor to the right sideplate and lift the sensor clear of the plotter. The order must include the part number, check digit designjett part description. Sservice conditions before the error occurred. Print cartridge and media loading pro- cedures, as well as front panel menu structures, are also provided.

Returning pens The pen carriage is returning to its station at the left of the plotter.

For model CA plotters, remove the outer electronics enclosure assembly. This product was designated to be returned to HP.

Throughput D-sized loaded vertically:

Life